[TiG] Tutorial: How to Install a Fixed Frame Projection Screen – Silver Ticket STR Series
Articles Blog

[TiG] Tutorial: How to Install a Fixed Frame Projection Screen – Silver Ticket STR Series

August 27, 2019


Hey, Shane here with That’s It Guys. If you’ve been keeping up with our Home
Theater on a Budget Series, we recently reviewed a fixed frame projection screen from Silver
Ticket Products. This video is going to cover how to assemble
that projection screen. I watched a few assembly tutorials and read
the instructions prior to putting my screen together, so I had a pretty solid idea on
how to do everything. The first thing you want to do is assemble
the aluminum frame face down. Lay out all of the pieces as shown here. Start sliding in the support clips, which
are used to hold the screen onto the frame. Make sure you slide in the number of support
clips specified for your screen as requested by the manual before bracketing everything
together. Now add in the upper and lower mounting brackets
in as shown here. These are the top brackets, these are the bottom brackets. The keyhole
slots with the smaller end should be on the top when the screen is mounted. Once all the clips and mounting brackets are
in place, start bolting the brackets into the frame, making sure you use the correct
screws. The screws with the flat heads go into the straight brackets. And the screws
with the round heads go into the corner brackets. Just work your way around the frame and get
everything assembled. After the frame is completely assembled, roll
out the screen material onto the frame. Line up the clips to the notches on the screen
as best you can, then start sliding in the tension rods around the perimeter. The rods
will keep the screen flat once everything is stretched out onto the frame. Once all the support rods are in place, start
hooking the pockets down onto the clips starting with the center on one end of the frame. Attach
the the screen to the center on the sides perpendicular to the starting point. Now comes the difficult part – clipping the
far end down. You’ll have to stretch the screen one to two inches to clip onto the
far side of the screen. This took quite a bit of effort to get clipped down when I did
it, but once it’s finally on there, you can work your way around the perimeter. Try
to do opposite ends as you clip the screen down to keep everything even. You may have to adjust the position of the
clips as the screen starts to even out, just make sure that every pocket is secured down. After the screen has been secured, the hardest
part of the installation has to be done, which is putting in the support rod that runs vertically
through the center of the screen. It is recommended to have someone help you out with this part,
but I’ll show you how to solo it. Initially, I thought you had to bend it into place, but
that would require an inordinate amount of work. The aluminum rod itself is about and
inch and a half longer than the opening of the frame. They actually state to go in diagonally
and to bend it to get it into position. I ended up doing this and then tapping it
into place with a hammer. If you have two people, you should be able to put your foot
on the frame while pulling up on the center of the rod until it clicks into the slot. If you are running into issues with this part,
I’d suggest taking a break and returning back to it. It will go into the slot, it just
requires a bit of patience and a lot of force. Once everything is assembled, now it’s just
a matter of aligning your projector and bolting the screen to the wall. For this, refer to
your manual for the minimum and maximum distance the mounting brackets can be apart and then
find the studs on the wall within that range. Get out your measuring tape and a level and
you’ll be set. Just remember to take into account the position of the bracket with the
elevation you want the screen at – it’s approximately 2.5” above the edge of the
screen. Mounting the screen is straightforward; Get
a friend to help you lift the frame onto the wall. Line the top mounting brackets up with
the screws on the wall and get the screws into the keyhole openings. Once the screen is mounted, you can make the
minor adjustments to the projector to get everything lined up. The nice part about this
projector screen is if you are off horizontally, you can slide it left and right several inches. So that covers the entire assembly and mounting
process for the Silver Ticket Products STR series frames. If you have any questions or
need help, comment below or head over to our forums in the link below. If this video helped
you out, leave us a thumbs up and some feedback below. For more tutorial videos and reviews, subscribe
to our YouTube channel and visit us at ThatsItGuys.com. Thanks for watching.

Only registered users can comment.

  1. Awesome, thanks for sending me the link. It didn't look sped up at all from start to finish. You just seem like a fast worker.

  2. Is there room behind the mounted screen for me to place LED lights with a channel tube around it ? I'm trying to avoid placing the LED strip on the sides. I think it would have a cleaner look if they are placed behind the screen. Just curious on how flush the screen lays to know if what I'm going for is even possible. Thanks

  3. Very helpful, just put up our 135" Silver Ticket tonight. Looks great with our BenQ W1070. Yeah, the tension bar was a bit of a bear but we got it. Great screen, was shooting for a nice "floor to ceiling" image & this is it.

  4. Your video shows there are two top mounting brackets and two bottom. do you need to hang your screen using both top and bottom brackets?

  5. hello. great video very helpful thank you so much. I want to buy this one but i wasn't sure about something. can i plug in chrome cast USB in it or it doesn't work on it?

  6. Question if I may? Is there a kit to make a 200-300" screen that's between 8-9 Feet High and 20-30 Feet Wide and or 15-20 Feet High to 60-80 Feet Wide?

  7. Getting the STR169110 tomorrow. Can't wait to get it up on the wall and see how well it works with my Epson 2030 projector. I am hoping it does as well as it advertises. We watch a large variety of media (tv, movies, streams, etc) and especially enjoy great 3D action movies.

  8. Thank you. This video was very helpful. Your screen shots of screws and which ones made it very helpful to understand how to do correctly.

  9. For mounting on the wall, are you supposed to just drive the screws into the studs, or do you need to use the plastic wall anchors somehow?

  10. just received my 106inch st screen and i love it assembly was easy(no parts missing) , not a pain in the ass to stretch the screen to pins.very happy with my purchase

  11. Just FYI, the manufacturer now recommends starting to stretch the screen at the corners, not the middle. I tried to stretch the screen using the "center lug" method and had one of the fiberglass rods snap. I emailed the manufacturer to get a replacement rod and they also provided the link to this video…

    https://www.youtube.com/watch?v=cHVxpnpIub4&feature=youtu.be

  12. Hi! I wanna know if the screen comes with the lights or do u have to buy them separately? And are so they all come with the lights I mean it can be any size and the lights come in the box ?

Leave a Reply

Your email address will not be published. Required fields are marked *